Influence of thickness and initial groove angle in M–K model on limit strain of 7B04 by considering through-thickness stress

Marciniack–Kuczinski (M–K) model is widely used to predict material’s forming limit curve (FLC). The prediction of FLC traditionally neglected through-thickness normal stress. However, it cannot be neglected in some forming processes. Much work has been done to study the effect of through-thickness normal stress on FLC with constant through-thickness normal stress or constant ratio of through-thickness normal stress and maximum principal stress. In addition, based on Nakazima test process, the ratio of through-thickness normal stress and maximum principal stress has been derived, which was a function of instantaneous thickness and loading path. Here, initial groove angle in M–K model was not considered. In this paper, uniaxial tension tests and Nakazima tests were performed on 7B04 aluminum alloy. Based on Hill 48 yield criterion and M–K model, the prediction model of FLC was established. The increase of thickness can enhance FLC. Meanwhile, it is necessary to consider through-thickness normal stress and initial groove angle in prediction model. On the left side of FLC, the effect of initial groove angle on FLC is weakened by increasing sheet thickness. On the right side of FLC, the effect of initial groove angle on FLC is strengthened by increasing sheet thickness. On the right side of FLC, the relation between limit strain points with different thicknesses is linear under one certain loading path. Thickness has decisive effect on through-thickness normal stress level and the changing trendy of through-thickness normal stress during calculation is different under different stress condition.     

H5飞机调油方法研究

对Ｈ５飞机经过了计算、论证、试飞，在此基础上提出了一种既安全又能充分发挥飞机飞行性能，同时又使动作程序化的调油方法－－规划调油法。用这种调油就可以大大地减少飞行员操纵飞机进的注意力分散，更利于集中精力操纵飞机，以保证飞行的安全。     

中心极限定理用于近似计算时必须注意的问题

本文着重指出,在运用中心极限定理近似计算独立同泊松分布随机变量之和的概率时,通常只注意了取n适当大的值,从而导致了差异较大的不同结果。本文指出了不仅要使n适当的大,而且也要使nλ足够地大。当X_h是其他离散型随机变量时,也要考虑类似的问题。     

板料应力成形极限判据的有限元分析程序

为了解决在板料成形有限元数值模拟中以依赖于加载路径的应变成形极限为判据所存在的问题,以板料塑性变形时所遵循的应力应变转换关系、H ill二次厚向异性准则为计算模型,基于有限元商用分析软件DYNAFORM,开发了用于板料塑性成形工艺的以应力成形极限为判据的有限元分析程序。利用该程序分析了两种拉深件的有限元数值模拟结果,实现了用应力成形极限图作为判据对板料成形极限的预测分析。所开发的以应力成形极限作为判据的有限元分析程序为分析多道次板成形的成形极限提供了新的手段。     

适用于含多个隐式极限状态方程的飞机结构系统安全分析新方法

工程复杂随机结构的概率安全分析中，最重要的两个步骤是建立所有失效模式的极限状态方程和计算所建立极限状态方程的失效概率。一般来说大型复杂工程结构的极限状态方程都是隐式的，且当材料参数、结构参数和外载荷等均为随机变量时，极限状态方程均为非线性的，为此文中提出了建立真实复杂结构多模式隐式极限方程的等效方法。该方法对于单个极限状态方程采用在均值点展开成线性项和高次项修正的方式，在概率等效的基础上，建立起原非线性隐式极限状态方程的概率等效线性显式极限状态方程。当结构系统所有极限状态方程都建立了其等效显式线性极限状态方程后，即可利用可得的可靠性分析方法来计算结构系统的等效失效概率。所提方法被用于真实飞机结构翼身连接接头的强度刚度多模式可靠性分析，与迭代响应面法计算结果的对比表明，所提方法具有较高的精度。并且所提方法可以与任何标准有限元程序相结合，而标准有限元程序是当今处理结构力学分析与设计的强有力的工具，文中方法提供了力学分析与概率安全分析相结合的合理连接，其应用前景将是十分广泛的。     

Collision Risk Mitigation in Geostationary Orbit

The short- and long-term effects of spacecraft explosions, as a function of the end-of-life re-orbit altitude above the geostationary orbit (GEO), were analyzed in terms of their additional contribution to the debris flux in the GEO ring. The simulated debris clouds were propagated for 72yrs, taking into account all the relevant orbital perturbations.The results obtained show that 6–7 additional explosions in GEO would be sufficient, in the long term, to double the current collision risk with sizable objects in GEO. Unfortunately, even if spacecraft were to re-orbit between 300 and 500km above GEO, this would not significantly improve the situation. In fact, an altitude increase of at least 2000km would have to be adopted to reduce by one order of magnitude the long-term risk of collision among geostationary satellites and explosion fragments. The optimal debris mitigation strategy should be a compromise between the reliability and effectiveness of spacecraft end-of-life passivation, the re-orbit altitude and the acceptable debris background in the GEO ring. However, for as long as the re-orbit altitudes currently used are less than 500km above GEO, new spacecraft explosions must be avoided in order to preserve the geostationary environment over the long term.     

正态模型结构可靠性贝叶斯下限的计算方法

本文对正态模型结构可靠度的贝叶斯精确下限的评估公式提供一种新的计算方法。该方法能达到任意给定的精度。计算复杂度可由O(n~2)降为O(n)。程序结构简单,使用方便。     

防止Ⅱ型驾驶员诱发振荡技术的研究

许多严重的飞行事故都与由速率限制引起的Ⅱ型PIO有关。针对如何预防PIO，首先介绍了自适应杆增益和软件限制环节的设计原理。然后以某带速率限制的电传飞机为例，运用同一理论，分析采用自适应杆增益和软件限制环节来改善速率限制的不利影响。仿真结果表明，自适应杆增益环节和软件限制环节都能抑制住PIO的发生，但两者组合加入抑制效果更好，飞行品质也能达到满意的程度。